Only system cookies are currently stored. Tracking of activities and analytics features are turned off.

At Jetski Army, we have exciting offers and news about products and services that we hope you'd like to hear about. To present you the offers that suit you the most, we need to know a few personal details about you. We will gather some of your activities on our website (such as which pages you've visited, etc.) and use them to personalize the website content and improve analytics about our visitors. In addition, we will store small piecies of data in your browser cookies. We promise we will treat your data with respect, store it in a secured storage, and won't release it to any third parties.
 

Your Ride

Tell us your ride so we can recommend articles and products.


Articles / Standup / 400 and 440 Modifications

400 and 440 Modifications

17 September 2018
Article 400 and 440 Modifications
There are still some nice 440’s out there - and - contrary to the “bigger is better” crowd - a well prepped 440 will run with most 550’s and run away from many AND - they are smoother and far more reliable ( with the exception of the 91 thru 95 550 SX reed motors ) -- AND -- not everyone has a bottomless checkbook.
IF - you have a stock 400 - or - 440 - 1976 thru 1983 - and you want to make it just a bit more “crisp” - then this is what you do. Remove the head and take it to the local machine shop and have them mill .080 from the surface. Yep - that will mill off the combustion chamber “lip” - not to worry - you CAN go as far as .120 - but - that is not needed here. Use a new OEM head gasket and re-install - making sure everything is super clean. Install a set of straighter bars to allow you to move further forward on the tray. Install an aftermarket intake grate - Jet Enterprises made the first and still the best - many people copied it - a Westcoast - Jetco - or PJS is just fine. Do NOT silicone between the grate and the ride plate. Check the prop to pump clearance and make sure it is tight - if it is not - install a new OEM prop. Quick turn steering is a great idea - and - how to do that is in the files - but - this and ride plates are personal preference - and nearly everyone has a “favorite” and most of them are wrong. Good luck. You should have “about” 180 to 190 PSI compression - make SURE. If you have a variance of 10 pounds or more - YOU HAVE ANOTHER PROBLEM - fix it first. IF - you have a 1981 thru 1983 - make SURE your choke has been removed and a primer installed - if you do not - you WILL be sorry. Very sorry. The above is ALL you should do - unless - you are prepared to go - all the way. The above will pull a 200 pounder out of the water and give most anyone a “good” ride. You should be in the 35 MPH range - but - it will take a bit to get there.

Want more - ??? That is all well and good - BUT - if you do not have the money to do it “all” - don’t start. The following mods need to be done “all together - at once” - no piecemeal.
Super Stock - Stage 2 - kickass 440 - Remove the motor and the pump and the driveshaft and install a bulkhead support plate. ( bet that sent most people running ) - Buy a dual waterline kit and install it - drilling out the brass fittings before installing - ( an option is a ½ inch single line - and that is fine ) - I recommend NOT using the stock water line - drill and install 2 new ones and cap off the old OEM line. Leave the bilge alone - it works fine. Carefully re-install the drive shaft with at least new seals - and preferably new bearings and seals. Re-install the pump with a new 15 degree stainless impeller - and - you should bore the reduction nozzle also - paper thin - with a new copper pipe to replace the now missing bilge outlet - silicone around the pump intake channel only.

Replace at LEAST the front crank bearing and all new crank seals ( 3- 92049-3006 ) . Have the top end bored to clean and get a new set of oversize pistons and rings to install - hone to 300 grit with a quality ( sunnen or similar ) hone. An OEM gasket kit will also be needed. Raise the exhaust port 3mm and widen it 2 mm on either side ( 4 mm total ) - “square” off the port shape a bit - raise the intake port 2 mm and lower it 4 mm - leave the ports with an arc ( same call it a smile port - NOT square ) - cut 4mm off the intake skirt of the piston - LEAVING a 10 mm wide section on either side - so the piston does not “rock and fall into a port. Do a GREAT job of chamfering the ports. Most heads are already drilled and tapped and have a brass plug in them near the spark plugs - remove the brass plugs or drill and tap (1/8th inch pipe thread ) new holes. Install 2 new straight brass fittings in these holes. Install that .080 milled head. Install intake manifold and match the manifold to the ports - as good as you can - some are off too far to get a perfect match - do your best. Install an aftermarket exhaust manifold or an exhaust diverter and match those ports also. ( L&S made the first and still the best exhaust manifold - but - others are OK - Westcoast - Jetco - PJS - whatever. Reassemble motor and carefully re-align to newly rebuilt pump shaft.

Hook the water lines up - One each to the newly installed nipples on the top of the head - or - split the ½ inch with a “Y” and then to each one. Run a pisser out the side from the exhaust manifold to BELOW the hull bond line ( so the water will drain from the motor when shut off ) - the other water line from the front of the head - will go to your new pipe. A Westcoast cast type is the best - with as short a body as you can make it - a Coffman is OK - as is a short body PJS. Usually a “T” is installed and another pisser on the other side is used - but - be careful you don’t divert too much water and burn up hoses and waterboxes. Even with three times the water going through - it can still get hot.

Disassemble the carb - install a new 2.0 float valve assy ( 2.2 or 2.5 CAN be used also ) - drill the top end jet ( non-removable brass disc ) with a “42 drill - which is about 1/16 - reassemble with new diaphrams - gaskets can usually be re-used. Same primer as described in the first section. Air filter / flame arrestor - is your choice ANYTHING but stock. Remember - boats don’t need air filters - but - they do need flame arrestors. Set both carb screws at 3/4ths turn out to START. Install carb and hook up throttle and primer.

Any other handling mods are purely personal preference and most are just fine - whatever floats your boat. You will NOT need race fuel - standard 90 octane ( preferably gas - NOT ethanol ) is all you need - a good pre-mix oil ( Redline Racing Oil is best - some prefer 927 ) 50 to 1 mix - this little screamer should have right at 190 PSI - and be in the just over 40 MPH range and get there really - really quick. AND - it should LIVE !!!
You “can” advance the timing - but - for ease of starting etc - I would leave it. 25 degrees BTDC is just fine.

By Cliff Jones

Comments

There are no comments yet. Sign in to leave one!



Related products